Questions & Answers

Q: QuestionDo KICKER CXA Mono subwoofer amplifiers work with factory-installed radios?

• A:Answer Yes, the KICKER CXA Mono line of subwoofer amplifiers is designed to work with virtually any factory-installed radio or aftermarket system.

Q: QuestionDoes this amplifier have a variable low-pass filter?

• A:Answer Yes, it has a variable low-pass-filter crossover adjustable from 50Hz to 200Hz, allowing you to fine-tune the frequencies sent to your subwoofer.

Q: QuestionCan I adjust the bass on this amplifier?

• A:Answer Yes, the amplifier features a 0-6dB bass boost, allowing you to fine-tune the low-frequency output to your liking.

Q: QuestionWhat kind of circuitry does this KICKER amplifier use?

• A:Answer This amplifier utilizes Class D circuitry, known for its efficiency and reliable power handling capabilities.

Q: QuestionWhat is the signal-to-noise ratio of this amplifier?

• A:Answer This amplifier boasts a 95dB signal-to-noise ratio, ensuring clear and high-quality audio output.

Q: QuestionWhat is the total power output of this amplifier?

• A:Answer This amplifier delivers a robust 800 watts of total power, ensuring ample power for your subwoofer system.

Q: QuestionWhat is the impedance of this amplifier?

• A:Answer This amplifier has an impedance of 4 ohms, which helps to ensure efficient power delivery to your speakers and maintain consistent audio performance.

Q: QuestionCan this push 2 12” kicker subs 2 ohm dual coil. Will it be sufficient. Or will it be getting to hot. Or do i need the 1200wat. Do i even need 2 subs. Will i make my trunk shake the way i want it to with 1? A lil input would be much appreciated.

Asked 5 years ago by Kest.

• A:Answer I originally had this paired with one Kicker Comp R 12 at 2 ohms. That was way too powerful for the Comp R because it kept blowing the sub despite Best Buy Geek Squad tech actually taking the time to ensure the output was matched and accurate to what that one Comp R 12 was supposed to be able to handle. It was explained to me that the blowing was likely due to this amp actually being more powerful than it's reported and not necessarily due to the Comp R 12 not being able to handle what it's supposed to. I recently upgraded to the Kicker Comp VX 12. Wow. I've got a bass knob installed. The bass know was previously turned all the way up when the Kicker Comp R was paired with this amp, and the gain on the amp was turned down lower to prevent the Comp R 12 from blowing. It still sounded good, but I figured I wanted to get more out of the amp by going with a better sub. The Kicker Comp VX 12 hits so much deeper and louder paired with this amp at 1 ohm (it's 1 ohm stable which is a huge deal!), AND that's wit the bass knob turned down to about 25% I want to give this sub some time to break in and am gradually turning up the bass knob. Summary is that this is perfect to pair with one Kicker Comp VX 12 with it wired at 1 ohm. I promise you won't regret it. Matthew 7:12

  Answered 5 years ago by cinnamonroll72

  Helpful (7)Unhelpful (1)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this amp work well with two 12 kicker comp r’s individual boxed 2 ohm fully loaded or should I purchase a bigger kicker amp? Each sub is 500 watt rms and 1000 watt peak power.

Asked 2 years ago by Christian.

• A:Answer The KICKER CXA800.1 is rated to develop 800 Watts RMS in to a 1-ohm load. The KICKER CompR 12" Subwoofer is rated at 500 Watts RMS and with using a pair of them (2) you would be at a total RMS power rating on your speaker system of 1000 Watts RMS. For maximum performance of your speaker systems, KICKER recommends using an amplifier that is rated to produce X Watts RMS that is within +/- 20% of your speaker systems RMS rated power. So, with a 1000 Watt RMS rated speaker system, KICKER recommends using an amplifier that falls within the 800-1200 Watts RMS range. Always keep in mind that smaller amplifiers will also sound great but just not get you the full output (SPL, loudness) potential of your speaker systems. If you have further questions, please feel free to reach out to KICKER Technical Support. Email: [email protected] Phone: 405-624-8510, Mon-Fri, 8:00-5:00 Central time .

  Answered 2 years ago by Kicker Customer Support

  
  Helpful (5)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionThis amp's specs say it doesn't need an LOC. It uses either FIT1, FIT2, or FIT+. The latest version 2019, shows this model to use FIT+ technology. Has anyone used this feature or are guys still installing this amp with an LOC?

Asked 4 years ago by Nino.

• A:Answer You will have to purchase speaker wire to RCA adapters. Kicker sells them on their website for about $15 I think. Hook those from your speaker wires to your amp. Be sure to switch the input button on your amp to HIGH instead of low. DO NOT USE THIS PLUS A REMOTE WIRE. You dont need a remote wire with amp wired this way. It senses signal from your speakers and automatically turns on.

  Answered 4 years ago by Broman

  Helpful (4)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI have a Dodge Challenger which requires a Line Output Converter. I noticed that it has a remote input in between the power cable input and also the ground input. Can this power the LOC without having to run power from the fuse box?

Asked 4 years ago by MrBanks.

• A:Answer If your referring to a kicker amp you do not need a loc, kicker makes a kisl which converts high level speaker input to rca. Its about 20 bucks and 4 butt connectors thats it. Your amp will sense power from from your speakers and power on and off automatically. So much easier and cheaper but yes you can also use the same power and ground on your amp to power the loc if you still decide to use it. Sound quality is better with the kisl, also with kisl you'll have the high/low input button on your amp to high. Check it out

  Answered 4 years ago by RyanVerified Purchase

  Helpful (3)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI bought this amp and I am intrested on buying a 10' subwoofer at 2 ohms that will handle the 600 rms rating. This amp has been updated and will do 1ohm now also. The max is 1600 watts. Does anyone have any suggestions?

Asked 5 years ago by Lolo.

• A:Answer It will do the job for a 10 it powers my 2 10' kicker subwoofers. Have the same amp.

  Answered 5 years ago by CALIFERO13Verified Purchase

  Helpful (3)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this amp work with a JL Audio Stealthbox that’s rated at 2 ohm mono at 400 RMS? I don’t believe the voice coils will be accessible. I’m confused because the amp says 4 ohm but people are running it at 1 or 2 ohms. I’m a noob thanks

Asked 1 year ago by Chris.

• A:Answer Yes make sure wiring configuration is at 2 ohm before connecting to amp

  Answered 1 year ago by JodyRVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI purchased this amp to power for door speakers they are kicker 200 W speakers will this work

Asked 4 years ago by Budman.

• A:Answer Yes it will

  Answered 4 years ago by RockVerified Purchase

  Helpful (2)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this work with a 6 channel cd player, car audio?

Asked 4 years ago by Paul.

• A:Answer It will work with almost any aftermarket head unit, and will fit most stock vehicles either directly or with an adapter. Your Best Buy audio installer will be able to tell you what is needed to fit your particular vehicle.

  Answered 4 years ago by GlibRemarkVerified Purchase

  Helpful (2)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this amp be good with a pair of Rockford Fosgate R2D4-10. I have the subs in a shallow mount box in my truck: https://rockfordfosgate.com/products/details/r2d4-10/ Any input would be much appreciated. Thanks!

Asked 5 years ago by JohnA.

• A:Answer Yes it will I have it on 12” Rockford Fosgate p2d4 sub in a ported enclosure

  Answered 5 years ago by iMac

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionHow can I connect my 4 speakers which I just bought that are jbl gx628 to my kicker amp800.1, and will it make it sound better??

Asked 1 year ago by Brandon.

• A:Answer sorry dude I didn’t hook mine up let Best Buy do it

  Answered 1 year ago by DeanVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionHey guys. I'm getting a pair of the 2016 Kicker CompR Dual 10 Inch subwoofers. Does this amp have the power to power those subs? It's going into a 2014 Tahoe with a stock head unit. Any information would help. Thanks.

Asked 2 years ago by Dez.

• A:Answer From what I can find, the RMS on those are 400W. So yes, I believe you would be paired well with this amp. Also depending on the Ohm on the pair you have (2 or 4), you can wire them to give the most from the amp. Parallel will half, series will double the ohms. Hope this helps.

  Answered 2 years ago by thesouth1Verified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWhat wire kit do you need for his amp?

Asked 4 years ago by Tony.

• A:Answer I used a skar 4 guage ofc wire kit I got this amp pushing a kicker l7 12

  Answered 4 years ago by Gamingdad1

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionCan i set this up as a 2 ohm load with my 2 4 ohm subs?

Asked 4 years ago by teddy.

• A:Answer As long as your subs are single voice coil you can. Wire them in parallel and you’ll get 2 ohms and roughly 600 watts of output from the amp.

  Answered 4 years ago by AdamVerified Purchase

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)