Questions & Answers

Q: QuestionWhat is the signal-to-noise ratio of this amplifier?

• A:Answer This amplifier has a signal-to-noise ratio of 100 decibels.

Q: QuestionDoes this amplifier come with mounting hardware?

• A:Answer Yes, mounting hardware is included with the amplifier.

Q: QuestionHow much power can this amplifier deliver to my subwoofer?

• A:Answer This amplifier can deliver up to 800 watts RMS to your subwoofer.

Q: QuestionWhat is the frequency response range of this Pioneer amplifier?

• A:Answer This Pioneer amplifier has a frequency response range of 10 hertz to 0.24 kilohertz.

Q: QuestionWhat kind of protection features does this amplifier have?

• A:Answer This amplifier features Pioneer's PCS (Protection Control System), which monitors voltage, current consumption, and temperature to ensure safe and stable operation.

Q: QuestionDoes this amplifier have a variable low-pass filter?

• A:Answer Yes, the amplifier has a variable low-pass filter with a range of 40 Hz to 240 Hz.

Q: QuestionWhat Guage wires is it recommended to power up this amp

Asked 4 years ago by CB.

• A:Answer 4 gauge, OFC

  Answered 4 years ago by Willy

  Helpful (2)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this amp push 2 Rockford-Fosgate 10" prime dvc Speakers

Asked 6 years ago by LeeRoy.

• A:Answer From what I understand, it should work. I run it on 2 12 inch kickers and it bumps!

  Answered 6 years ago by ccccooorrryyy

  Helpful (2)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI ran it on a 8” 1200 max watts 4 ohms wired it so it played as a 2ohm and now the speaker doesn’t play as well i can hear it idling with my car its the speaker bad?

Asked 4 years ago by Jonathan77.

• A:Answer You can hear it idle with the car? I can only assume you hear a buzz that would be a bad ground. Never match speaker to amp by max output always go by RMS.

  Answered 4 years ago by Tabossco

  Helpful (1)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionIs it 1ohm stable?

Asked 3 months ago by Yosy.

• A:Answer Yes, it will have a continuous output of about 800 W RMS x 1-Channel, with a 1 Ohm load.

  Answered 3 months ago by Pioneer Electronics Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWill this amp power 2-12' MTX Jackhammers.

Asked 4 months ago by DavidB.

• A:Answer In general, you want to match the continuous output of the amplifier to the nominal power rating of the speaker. Here is the power rating for the GM-DX81: 300 W RMS x 1-Channel - 4 Ohm 500 W RMS x 1-Channel - 2 Ohm 800 W RMS x 1-Channel - 1 Ohm If you connect two speakers, each speaker will take half the power.

  Answered 4 months ago by Pioneer Electronics Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWould this be a good match for a Cerwin Vega vs12 sh 4 ohm dual voice coil sub? Looks like specs are a good match.

Asked 4 months ago by Anonymous.

• A:Answer If the final impedance is 4ohms, then it should be a good match.

  Answered 4 months ago by Pioneer Electronics Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWill this amp power a 18 inch punch sub?

Asked 6 months ago by Gregas.

• A:Answer Dont buy it its junk

  Answered 6 months ago by ThatRedXJVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWhat are the dimensions? Are there provisions for mounting it?

Asked 7 months ago by Anonymous.

• A:Answer Product Height - 4.44 inches Product Width - 10.8 inches Product Depth - 12.96 inches Product Weight - 7.55 pounds The amplifier will come with basic screws to hold the amplifier in place. Some installs may require more. I would suggest consulting with a local Best Buy. They can advise you on exactly what you may need.

  Answered 7 months ago by Pioneer Electronics Team

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionI’m looking at getting this amp. I have a Kicker 12 inch subwoofer. How does Best Buy adjust this amps gain to my HEAD UNIT? I don’t want CLIPPING in my system! Let me know how BB does this as it’s important. Thanks.

Asked 1 year ago by GregAmp.

• A:Answer As long as you have a good ground your amp won't clip.

  Answered 1 year ago by TwnShtVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionHow should I wire this with 2 kicker comp r 12s and Chrysler 300 factory radio?

Asked 2 years ago by NvWatts.

• A:Answer Amp not powerful enough

  Answered 1 year ago by TwnShtVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question

Q: QuestionWill , this amp run to kicker c competition subs 10 inch

Asked 2 years ago by Chad.

• A:Answer Yes it will

  Answered 1 year ago by EnriqueVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this amp run 2 KICKER - Solo-Baric L7T 10" Single-Voice-Coil 2-Ohm Loaded Subwoofer Enclosure

Asked 3 years ago by Chevy77.

• A:Answer Yes

  Answered 2 years ago by EricwVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionWill this work with a 12” rockford fosgate p3? It’s lowest is 600watts and highest is 1200. I had a pioneer GM-D8601, however it broke, so I’m trying to find a good amp.

Asked 3 years ago by Customer.

• A:Answer Not enough power

  Answered 1 year ago by TwnShtVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this questionShow more answers (1)

Q: QuestionI have two kicker comp r 12’s and have them on the pioneer 1600 amp should I bridge the hookup are hook them up regular and I was told that you could run two more 12’a because being 2 ohm is that true

Asked 3 years ago by Mar123.

• A:Answer As long as your total load doesn’t equal less then 1 ohm you can power however many you want

  Answered 2 years ago by EricwVerified Purchase

  Helpful (0)Unhelpful (0)ReportAnswer this question